• Confining pressure : Upto 6000 psi
• Temperature control range : 0°C - 150°C
• Flow capacity : 0.03-30 mL/min

• Flow studies in porous media
• Oil recovery applications including pressure maintenance and chemical EOR
• Fracturing studies in reservoir rocks

• Core sample : 1” (length 5-12 cms)
• Injection fluid : Dead oil/Diesel (600 ml)
• Displacing fluid : Toluene (2.5 L)
• Other chemicals as per experimental requirements

• Research grade equipment and have multiple data collection modes including fluorescence, phosphorescence, chemiluminescence and bio-luminescence.
• Source: continuous wave source of Xenon Arc Lamp.
• Detector spectral range 200-900 nm.
• Analysis software enables Spectra scan, 3D-Spectra Scan, quantification, Single read, Time Drive, Kinetics, Anisotropy/Polarization (in both in Spectra Scan and Single Read), Intracellular ion concentration, Quantum yield (Relative and Absolute), Quenching, Lifetime, Absorbance, Wavelength programs, Validation, Pre-Scan, Synchronous scan mode (constant energy and wavelength), 3D Synchronous scan.
• Complete Peltier system with all required accessories enabling Peltier effect temperature control, Temperature range 0⁰ C to ~100⁰ C.
• Suitable Accessories for Liquid & Solid Samples (holder for liquid, thin Film, powder, Single Crystal)

• Widely used in bioanalysis for measuring small amounts of drug and for studying drug-protein binding

• Liquid, Thin Film, Powder

• Spectrometer Frequency : 400 MHz
• Solution State Probes :
  Royal Probe - A Multinuclear Probe with Variable temperature facility to cover nuclei preferably 15N to 31P and Variable temperature accessory for -100oC to +150oC. Automatic tuning and matching for all observation Nuclei.
  TH5 Probe - Observation Nuclei 15N to 31P and 1H and 19F with Automatic tuning and matching for all observation Nuclei.
• Spectroscopy by NoD solvent
• Auto-sampler
• Delta NMR Data Processing Software

Measurement range: 0.3nm – 10.0 microns* (diameter).
Measurement principle: Dynamic Light Scattering
Minimum sample volume: 12µL
Accuracy: Better than +/-2% on NIST traceable latex standards
Precision / Repeatability: Better than +/-2% on NIST traceable latex standards
Sensitivity: 0.1mg/mL (Lysozyme)

Measurement range: 3.8nm – 100 microns (diameter)*
Measurement principle: Electrophoretic Light Scattering
Minimum sample volume: 150µL (20µL using diffusion barrier method)
Accuracy: 0.12µm.cm/V.s for aqueous systems using NIST SRM1980 standard reference material
Sensitivity: 10mg/mL (BSA).

Analyzer

• 180° double focusing hemispherical analyzer
• High-efficiency electron transfer lens
• 128-channel detector

X-ray Source

• Al Kα micro-focused monochromator
• Variable spot size (30–400 µm in 5 µm steps)

Charge Compensation

• Dual-beam source
• Ultra-low energy co-axial electron and Ar+ ion beam

EX06 Ion Gun

• Energy range 100 eV to 4 keV

Sample Handling

• 4-axis sample stage
• 60 X 60 mm sample area
• 20 mm maximum sample thickness

Vacuum System

• Two 250 l/s turbo molecular pumps
• Auto-firing, 3 filament TSP

Software

• Avantage software including offline data processing sampling capabilities
• Tilt Module
• Sample Bias Module

• Glass Coatings
• Polymers
• Batteries
• Graphene
• Solar Cells
• OLEDs
• Metals and Oxides
• Bio-surfaces
• Thin Films
• Semiconductors
• Ceramics
• Catalysts

Declaration of the chemical and physical composition of all samples is appreciable. The Users are ensured that the information will be kept confidential. The following restrictions apply on samples:

1. Sample holders soldered with Pb not allowed. If soldering is necessary on the sample holder one should use Ag soldering.
2. No radioactive, toxic or explosive material will be accepted for analysis.
3. Analysis on thin and thick films of all kinds of oil is disallowed.
4. Thin films of molecules with low melting point, say below 80°C at ambient pressure are not allowed.
5. Loose Powder samples are acceptable but sputtering on such sample may not be undertaken.
6. All kinds of spin-coated, drop-cast samples should be properly dried and desiccated, before providing for analysis.
7. Liquid phase prepared samples (e.g. LB films) should be rinsed in proper solvents and dried before submitting for analysis.
8. Sticky polymer films not allowed. If polymers need to be analysed, they need to be spin coated and dried. However, proper self-assembled thin films (below 50 nm thickness) of polymers are allowed.
9. Thick Compact samples (green or sintered) samples with high fraction of pores/ voids are to be avoided.
10. Smaller sample dimensions are preferred. For example, sample thickness of ~1-2mm and 5mm length/width/diameter are ideal. Although, samples are acceptable as long as it is greater than 10mm in height and 10-15mm in length/ width/ diameter.

Note: The Laboratory reserves the right to reject any accepted analysis request at its discretion in the interest. Safety of the instrument and its operators.

• Double beam, double monochromator, fully automatic UV-VIS-NIR Spectrophotometer with complete computer controlled.
• The spectrophotometer accurately measure the direct transmittance and absorbance in the wavelength range of min 175 nm to ~3300 nm with continuous variable bandwidth selection capability.
• Enable to measure all kinds of samples ranging from the thin solid films, liquids and powder samples.
• Source: Tungsten-halogen and deuterium lamps with built-in mechanism in order to automatically switch the light source during the measurement of the entire UV-VIS-NIR wavelength range for all the samples.
• Detector: Photomultiplier tube (PMT) detector for the UV-Vis wavelength range and cooled PbS/InGaS or suitable detector for the NIR wavelength range.
• Compatible integrating sphere of min 100 mm diameter or more (with built in PMT and PbS detectors) for measurement of diffuse reflectance/diffuse transmittance of solids, thin films and powder. Wavelength range: 250-2500 nm.
• All with necessary sample holders and accessories. Quartz cuvette: Solid/powder Sample Holder; Thin Film Holder.

• To determine the optical properties (transmittance, reflectance and absorbance) of research and manufacturing materials.

• Liquid, Thin Film, Solid, Powder